TPU1164D50TPU1164D50￠

品牌：进口 产品规格：25KG 产地：广东东莞 包装说明： CAS/标准: 运输说明： TPU 1164D50 TPU 1164D50￠▲‘PP YPJ-1215C
▲‘TPE G7705
▲‘PC V1900
▲‘PP HP400N
▲‘PP 5143H
▲‘PP D1189
▲‘TPEE 2551
▲‘PA6 6GF35HREC
PC/TPV A64CI
▲‘PA6 C538XTV30
▲‘ABS PA-763A
PMMA MI-8E
▲‘PC PDX-E-99689


TPU 1164D50 TPU 1164D50￠Long term supply of PA66 has higher melting point in polyamide material. In product design, a PA66 shrinkage between 1%~2%.
Now on the market circulation of many disposable nozzle by modification of the same material can reach the original material, but the price is relatively cheaper than raw materials, so as to give our customers a lot of cost saving.
U.S. liquid nitrogen RF-7007, RL4540
DuPont 101F, 101F-NC010, 101L, 101L-BKB009, 101L-NC010, 1032L, 103F, NC010, 103FHS, 103HSL, 10B, 10B40, 11C40-BK, 13T1, BK, 122L3426408HS, 450HSL NC010, 45SHB NC, 490, 408L, 45054G15HSLR, BK031 5514
0G13HS1-L, 70G13HS1L, 70G13L, 70G13SH1L, 70G20HSL, 70G25HSL, 70G25HSLR-BK099, 70G30HSLR, 70G33HS1-L, 70G33HS1L-NC010, 70G33HSIL (BK), 70G33HSIL (NC), NC010 (BK), 70G33L,
In order to improve the adhesion of the coating on the plastic surface and improve the appearance of the plastic, the surface of the ABS must be pretreated before coating. (1) the internal stress is easy to form when the plastic ABS is formed, and the stress concentration is easy to crack. The annealing treatment or the whole surface treatment can be used to eliminate stress. The annealing treatment is to heat the ABS plastic parts under the hot deformation temperature, that is, 60 DEG C, the insulation 2h. In order to reduce equipment investment, the whole process can be used to improve the surface condition. The formula and process of the whole process are listed in table 1. Table 1 the entire surface treatment project formulation and process parameters / 1 / 3 / C water temperature at room temperature the processing time of /mi15 - 20 (2) in addition to oil ABS plastic surface often Zhanyou oil, hand sweat and release agent, it will make the paint poor adhesion, coating cracking, blistering and shedding. Degreasing treatment should be carried out before painting. ABS plastic parts are usually cleaned with gasoline or alcohol, and then chemical degreasing. The process formula is listed in table 2. Table 2 degreasing process formula and process parameters of sodium hydroxide (S/L) Project 50 ~ 70 sodium phosphate (S/L) 20 ~ 30 sodium carbonate (S/L) from 10 to 20 surfactant (S/L) 5 ~ 10 / 50 ~ 60 DEG C temperature processing time /min10 to thoroughly clean the residual lye surface chemical oil 15 Zui, and pure water after the clean, dry or drying. (3) in addition to electricity and dust plastic products are insulators, surface resistance is generally around 1013, easy to produce static electricity. After being charged, it is easy to absorb the fine dust in the air and attach to the surface. It is very difficult to remove the dust by electrostatic adsorption. It is better to use high pressure ionization air flow to remove dust.
TPV thermoplastic ethylene propylene three dynamic vulcanization elastomer / rubber main performance: TPV easy to weld, reusable, environmentally friendly non-toxic. The main features of three TPV thermoplastic dynamic vulcanization elastomer / EPDM rubber: 1, excellent aging resistance and good weather resistance, heat resistance; 2, excellent anti deformation performance of Yong for a long time; 3, good tensile strength, high toughness and high elasticity; 4, and excellent environmental performance can be used repeatedly; 5, excellent electrical insulation properties; 6, hardness range; 7, using temperature range; 8, color variety, are completely transparent, translucent, light color series, easy coloring, easy to process; 9, with PP, PA, PC, ABS, PS, PBT, and PET a variety of materials such as co injection or extrusion molding. TPV 8221-60, TPV 203-50, TPV 281-45MED, TPV 281-55MED, TPV 281-64MED, TPV 281-73MED